Mathews Inc.
Fletching Tools
Equipment
Contributors to this thread:
JB 09-Oct-18
wyobullshooter 09-Oct-18
StickFlicker 09-Oct-18
JTV 09-Oct-18
Sling Shot 09-Oct-18
RJ Hunt 09-Oct-18
JB 09-Oct-18
midwest 09-Oct-18
keepemsharp 09-Oct-18
Dale06 09-Oct-18
Buffalo1 09-Oct-18
DMTJAGER 09-Oct-18
Matt 10-Oct-18
dmann 10-Oct-18
JB 10-Oct-18
grubby 10-Oct-18
Ironbow 10-Oct-18
Buffalo1 10-Oct-18
JB 10-Oct-18
midwest 10-Oct-18
Boatman71 10-Oct-18
VogieMN 10-Oct-18
wyobullshooter 10-Oct-18
TD 10-Oct-18
Kodiak 10-Oct-18
From: JB
09-Oct-18
Before I got fat and lazy, I used to tinker with fletching my own arrows. Then I went the simpler route with the shrink wrap fletching. Reading the Blazer thread motivated me a bit and I’m going to get back into the game. That being said, what’s your recommendation for adhesive and jigs. Am shooting the Easton Injections. Any tips would be greatly appreciated!

09-Oct-18
I use an Arizona E-Z Fletch Mini, arrow wrap, Blazers, and Loc-Tite Ultra Gel to fletch my Axis shafts. Been using this setup for years with zero adhesion issues.

From: StickFlicker
09-Oct-18
I like the Arizona E-Z Fletch as well. I just use Fletchtite on my FMJ's and Blazers.

From: JTV
09-Oct-18
Arizona Mini-Max (does vanes up to 2.25") and PineRidge glue, rough the shaft first with brown or green scotch brite, wipe with paper towel and denatured alcohol .. dont over use the glue on the vanes, 2 or 3 drops and spread with a small piece of wire, dont let it seep down into the innards of the jig... you can clean the jig with acetone, I fill up a glass and cover the jig with acetone for a bit to remove residue... make sure it is "glass" or a can, if it is a plastic "glass" the acetone will melt it...

From: Sling Shot
09-Oct-18
It depends on what you are fetching. For the most part I have been using the EX-Fketchb with Fletch Flex vanes. I stroped using Blasers when they put advertising on every vane.

From: RJ Hunt
09-Oct-18
Arizona ez fletch here also.

From: JB
09-Oct-18
Thank you for the tips. I am leaning toward the Flex Fletch, but not 100% sure yet.

From: midwest
09-Oct-18
Arizona mini for the short, Blazer type vanes. Bitzenburger for everything else.

I fletch my Flex Fletch FFP 360's on a wrap, Zing primer on the base, and same glue as Wyobull.

From: keepemsharp
09-Oct-18
Have an antique Hoyt tri-heli fletch, has been going strong for 40 years and does three at a time, any angle you want.

From: Dale06
09-Oct-18
Been fletching my own for 35 years I only use 4” feathers and vanes Bitzenberger right helical Fletch tite platinum And I use onestringer wraps

From: Buffalo1
09-Oct-18
What are you wanting to fletch- feathers or vanes?

What length are you want to fletching are you wanting to use?

Do you plan to use a wrap? If yes, what length?

From: DMTJAGER
09-Oct-18
AZ EZ fletch. I've looked at every fletching jig out there under $100 and for $50 it doesn't get any better or simpler than a AZ EZ jig. And the jig is impervious to acetone so all you need to do to clean it up is soak the arms in acetone for 5-10 minuets and it comes out spotless.

From: Matt
10-Oct-18
AZ EZ fletch mini

From: dmann
10-Oct-18
I do the same as most of the others, az ez fletch mini, loctite gel, and usually use a wrap. Fletching blazers.

From: JB
10-Oct-18
Buffalo1 - Vanes. Haven’t decided length yet. Wasn’t looking at wraps, but the advice is pointing that way. Definitely has my curiosity up.

From: grubby
10-Oct-18
I have the AZ mini and it has worked great. I'm planning on getting a Bitz so I can play with 4 fletch though.

From: Ironbow
10-Oct-18
I bought my first Bitzenburger in 1975, another in 1980 so I could have one set up LW and the other RW and not switch them around. I can do any length fletch. I love to play with lots of fletching combos, from 1.5" vanes to 5" feathers and even flu flu's.

From: Buffalo1
10-Oct-18
JB

Your vane/feather can be a determining factor on the jig itself. Some jigs max out at 2.25” vanes. Others can handle any length vane/feather.

Both vane/feathers have their pros & cons.

If you decide on wraps Onestringer.com offers it all- length, color, etc.

Good luck on your pursuit.

From: JB
10-Oct-18
Awesome! Thank you!!

From: midwest
10-Oct-18
Onestringer is awesome and super fast shipping!

From: Boatman71
10-Oct-18
I have used the same AZ EZ Fletch for 20 years. They work great. A buddy of mine bought the mini and cannot fletch anything larger than a 23 shaft.

From: VogieMN
10-Oct-18
Arizona Ez Fletch Mini. I also have a Bitzenberger but with the Blazer vanes I could juts not get a helical on them, but the mini does an amazing job.

10-Oct-18
Onestringer +2. Although I use Blazers on my FatBoys for 3D without arrow wraps and have never had a problem, the arrow wraps I use on my hunting arrows allow for a nearly indestructible bond. The only thing I do is wipe the wrap with denatured alcohol. Make sure you don't use rubbing alcohol...it contains oil.

VogieMN brings up a point I take for granted if you're going to use a short vane such as a Blazer. A fletcher that allows for longer vanes is designed to provide helical along the entire length of the clamp. The shorter the vane, the less helical that can be applied. An Arizona Mini is designed for shorter vanes, so it puts more helical in a shorter distance. You won't find another fletcher that puts more helical on a short vane. The more helical, the more drag and stabilization. Extremely helpful when shooting broadheads.

From: TD
10-Oct-18
Correct. I think many folks having issues with broadheads are shooting with no helical or even offset, amazing how many prebuilt arrows are sold as straight fletched.

AZ mini is a great tool for 2" vanes. Bitz for everything else. I'm really liking the zing primer, cuts prep time way back and always get great bonding combined with the Ultra Gel Control.

From: Kodiak
10-Oct-18
I have a bitz but I only shoot 5" shields. Works great.

  • Sitka Gear